5300 Series Anti Static Table Mat

From: $55.60

Anti Static Table Mats are installed with (2) two snaps on the corners of the long side to connect common point ground, wrist straps, and monitors (if desired) separately.

Prices

SizesQty 1-9Qty 10+
2' x 3'$55.60 USD$44.88 USD
2' x 4'$68.30 USD$54.64 USD
2' x 5'$81.00 USD$64.80 USD
2' x 6'$93.70 USD$74.96 USD
30" x 5'$96.88 USD$77.50 USD














Specs

► Meets ANSI / ESD STM 4.1 Standard using FTMS 101C Method 4046.

► Lead-Free. Recyclable. Meets European Union (EU) Restriction of Hazardous Substances Directive (RoHS) regulating the reuse of products used in electrical and electronic equipment.

PropertiesUnitsTypical aluesTest Method
Material-Nitrile Butadiene Rubber / Carbon-
ThicknessInches.08ASTM D-2103
ThicknessMillimetres2ASTM D-2103
Tensile Strength • Top Layerkg / sq. cm> 120ASTM D-412
Tensile Strength • Bottom Layerkg / sq. cm> 160ASTM D-412
Tear Strength • Top Layerkg / sq. cm> 90ASTM D-412
Tear Strength • Bottom Layerkg / sq. cm> 100ASTM D-412
Elongation • Top Layer%350ASTM D-412
Elongation • Bottom Layer%250ASTM D-412
Hardness • Top LayerShore A50ASTM D-2240
Hardness • Bottom LayerShore A60ASTM D-2240
Gravity • Top Layer-1.3ASTM D-792
Gravity • Bottom Layer-1.4ASTM D-792
ESD Surface Resistance • Top Layerohms / square< 109ASTM D-257
ESD Surface Resistance • Bottom Layerohms / square< 105ASTM D-257
Volume Resistivity • Top Layerohms / square< 108ASTM D-257
Volume Resistivity • Bottom Layerohms / square< 104ASTM D-257
Static Decayseconds< 0.01EIA-541
Temperature ToleranceFahrenheit / Celsius187F / 86C-

Connect Grounding Cables to Mats

• Improve grounding by installing snaps to connect grounding cables onto mats.

• The grounding cables should be mat grounds, or common point grounds.

ESD Grounding Method for a Mat Grounding Cable

ESD Grounding Method for a Common Point Ground

The top anti static side of the mat collects static off of equipment and tools laid on top of it at a static dissipative rate, (1 x 106 to 9 x 108 ohms / square).

The bottom of the mat then conducts static to ground at a conductive rate, (1 x 103 to 9 x 104 ohms / square).

ESD Resistance Chart for an Anti Static Mat

However, if the mat is laying on top of a bench or floor made of an insulating material (like wood tables) you will need to install snaps and connect the mat to an electrical outlet with a grounding cable.

ESD Grounding Method for an ESD Workstation

It’s recommended you have grounding cables attached for every 5 feet of mat. They should not be “daisy-chained” together. Instead, directly connect the grounding cables to the electrical outlet.

Electrical outlets typically are the best path to ground the mat in any building because they follow the piping to the Earth’s electrical field underneath the building.

When connected to the electrical outlet, the mat is in electrical balance with the positive and negative charges of the building you are using it in.

ANSI / ESD S4.1 Test Data

The border line between conductive and static dissipative is 1 million ohms per square. This is also referred to as 1 meg ohm or 1 x 106 ohms / square.

ESD Resistance Chart for 5300 Series Anti Static Mats

To satisfy the ANSI / ESD S4.1 Worksurfaces – Resistance Measurements test standard the top static dissipative part of the mat was measured using resistance-to-groundable point and resistance point-to-point tests.

ANSI / ESD S4.1 guidelines at section 8.0 recommend resistance-to-groundable point (RTG) tests should find the top surface of grounded mats measure between 1 x 106 and 1 x 109 ohms / square.

Resistance point-to-point (also known as top-to-top or RTT) tests should measure the ESD resistance of the top surface of the mats at greater than or equal to 1 x 106 ohms / square.

As viewable in our diagrams, all 5300 Series mat samples were recorded within the acceptable range between 1 x 106 and 1 x 109 ohms / square, regardless of humidity, to meet the current S4.1 standard.

ESD Resistance Chart for Low Relative Humidity Test of 5300 Series Anti Static Mat

In our low relative humidity test, the sample with the least resistance measured 1.2 x 107 ohms / square.

The mat sample with the highest resistance measured 3.9 x 107 ohms / square.

ESD Resistance Chart for Moderate Relative Humidity Test of 5300 Series Anti Static Mat

In our moderate relative humidity test, the sample with the least resistance measured 1.0 x 107 ohms / square.

The mat sample with the highest resistance measured 9.8 x 107 ohms / square.

Reviews

There are no reviews yet.

Be the first to review “5300 Series Anti Static Table Mat”

You may also like…