5300 Series Anti Static Bench Mat

From: $38.12

 
 
Clear

• Eliminates Static from Work Bench. Installed with (2) two snaps on corners of long side.

Prices

SizesQty 1-9Qty 10+
2' x 3'$38.12$34.65
2' x 4'$47.02$42.75
2' x 5'$54.20$49.27
2' x 6'$63.28$57.53
30" x 5'$65.56$59.60











Specs

► Meets ANSI / ESD STM 4.1 Standard using FTMS 101C Method 4046.

► Lead-Free. Recyclable. Meets European Union (EU) Restriction of Hazardous Substances Directive (RoHS) regulating the reuse of products used in electrical and electronic equipment.

PropertiesUnitsTypical aluesTest Method
Material-Nitrile Butadiene Rubber / Carbon-
ThicknessInches.08ASTM D-2103
Tensile Strength • Top Layerkg / sq. cm> 120ASTM D-412
Tensile Strength • Bottom Layerkg / sq. cm> 160ASTM D-412
Tear Strength • Top Layerkg / sq. cm> 90ASTM D-412
Tear Strength • Bottom Layerkg / sq. cm> 100ASTM D-412
Elongation • Top Layer%350ASTM D-412
Elongation • Bottom Layer%250ASTM D-412
Hardness • Top LayerShore A50ASTM D-2240
Hardness • Bottom LayerShore A60ASTM D-2240
Gravity • Top Layer-1.3ASTM D-792
Gravity • Bottom Layer-1.4ASTM D-792
ESD Surface Resistance • Top Layerohms / square< 109ASTM D-257
ESD Surface Resistance • Bottom Layerohms / square< 105ASTM D-257
Volume Resistivity • Top Layerohms / square< 108ASTM D-257
Volume Resistivity • Bottom Layerohms / square< 104ASTM D-257
Static Decayseconds< 0.01EIA-541
Temperature ToleranceFahrenheit / Celsius187F / 86C-

Connect Grounding Cables to Mats

To improve the grounding of the mat you can connect it to a dedicated path to ground by attaching grounding cables to the snaps pre-installed on it.

ESD Grounding Method for a Mat Grounding Cable

The grounding cable should be either a mat ground, or a common point ground.

ESD Grounding Method for a Common Point Ground

We recommend you having these wirings attached for every 5 feet of matting. They should not be “daisy-chained” together. Instead, directly connect the wires to the electrical outlet.

Electrical outlets typically are the best path to ground the mat in any building because they follow the piping to the Earth’s electrical field underneath the building.

When connected to the electrical outlet, the mat is in electrical balance with the positive and negative charges of the building you are using it in.

To improve the grounding of the mat you can connect it to a dedicated path to ground by attaching grounding cables to the snaps pre-installed on it.

The grounding cable should be either a mat ground, or a common point ground.

We recommend you having these wirings attached for every 5 feet of matting. They should not be “daisy-chained” together. Instead, directly connect the wires to the electrical outlet.

Electrical outlets typically are the best path to ground the mat in any building because they follow the piping to the Earth’s electrical field underneath the building.

When connected to the electrical outlet, the mat is in electrical balance with the positive and negative charges of the building you are using it in.

ESD Grounding Method for a Mat Grounding Cable

ESD Grounding Method for a Common Point Ground

ANSI / ESD S4.1 Test Data

The border line between conductive and static dissipative is 1 million ohms per square. This is also referred to as 1 meg ohm or 1 x 106 ohms / square.

ESD Resistance Chart for 5300 Series Anti Static Mats

To satisfy the ANSI / ESD S4.1 Worksurfaces – Resistance Measurements test standard the top static dissipative part of the mat was measured using resistance-to-groundable point and resistance point-to-point tests.

ANSI / ESD S4.1 guidelines at section 8.0 recommend resistance-to-groundable point (RTG) tests should find the top surface of grounded mats measure between 1 x 106 and 1 x 109 ohms / square.

Resistance point-to-point (also known as top-to-top or RTT) tests should measure the ESD resistance of the top surface of the mats at greater than or equal to 1 x 106 ohms / square.

As viewable in our diagrams, all 5300 Series mat samples were recorded within the acceptable range between 1 x 106 and 1 x 109 ohms / square, regardless of humidity, to meet the current S4.1 standard.

ESD Resistance Chart for Low Relative Humidity Test of 5300 Series Anti Static Mat

In our low relative humidity test, the sample with the least resistance measured 1.2 x 107 ohms / square.

The mat sample with the highest resistance measured 3.9 x 107 ohms / square.

ESD Resistance Chart for Moderate Relative Humidity Test of 5300 Series Anti Static Mat

In our moderate relative humidity test, the sample with the least resistance measured 1.0 x 107 ohms / square.

The mat sample with the highest resistance measured 9.8 x 107 ohms / square.

The border line between conductive and static dissipative is 1 million ohms per square. This is also referred to as 1 meg ohm or 1 x 106 ohms / square.

To satisfy the ANSI / ESD S4.1 Worksurfaces – Resistance Measurements test standard the top static dissipative part of the mat was measured using resistance-to-groundable point and resistance point-to-point tests.

ANSI / ESD S4.1 guidelines at section 8.0 recommend resistance-to-groundable point (RTG) tests should find the top surface of grounded mats measure between 1 x 106 and 1 x 109 ohms / square.

Resistance point-to-point (also known as top-to-top or RTT) tests should measure the ESD resistance of the top surface of the mats at greater than or equal to 1 x 106 ohms / square.

As viewable in our diagrams, all 5300 Series mat samples were recorded within the acceptable range between 1 x 106 and 1 x 109 ohms / square, regardless of humidity, to meet the current S4.1 standard.

In our low relative humidity test, the sample with the least resistance measured 1.2 x 107 ohms / square.

The mat sample with the highest resistance measured 3.9 x 107 ohms / square.

In our moderate relative humidity test, the sample with the least resistance measured 1.0 x 107 ohms / square.

The mat sample with the highest resistance measured 9.8 x 107 ohms / square.

ESD Resistance Chart for 5300 Series Anti Static Mats

 

ESD Resistance Chart for Low Relative Humidity Test of 5300 Series Anti Static Mat

ESD Resistance Chart for Moderate Relative Humidity Test of 5300 Series Anti Static Mat

Reviews

There are no reviews yet.

Be the first to review “5300 Series Anti Static Bench Mat”

Your email address will not be published. Required fields are marked *

You may also like…